Fuel, Propane and Water

5 lb. Propane Cylinder.

5 lb. propane tank. Compact and light weight.

(DOT 5 lb cylinder 12" H x 8" diameter).

5 lb. Propane Cylinder Bracket. AT's aluminum propane bracket, sized to fit a 5 lb. propane tank. Compact and light weight.

(DOT 5 lb cylinder 12" H x 8" diameter).

10 lb. Propane Cylinder.

10 lb. propane tank. Compact and light weight.

(DOT 10 lb cylinder 17.4" H x 8.9" diameter) .
Contains 2.4 gallons of propane.

AT has designed an aluminum bracket for the Manchester Tank 10 lb propane cylinder.

The brackets are made from 1/8" thick aluminum and have rubber bump stops to hold the cylinder off the bracket. The cylinder is held in place by two stainless steel T Bolt clamps. There are pre-drilled holes in the bracket.

BRACKET:
Size: 12.375" T x 9.5" W x 4.75" D (314mm x 241mm x 120mm)
Weight:2.5 Lbs (1.13 Kg.)
1/8" Thick aluminum
Two Stainless Steel constant tension clamps

The bracket and cylinder combined weight is 17 lbs.(7.7 Kg) and it is 18" tall (457mm) with a maximum diameter of 10.3"(226mm).

CYLINDER:
The Manchester 10 lb propane cylinder that fits into this bracket is 17.4" tall x 8.9" in (442mm x 226mm) diameter and holds 2.4 gallons of propane.

Use the AT Corner Bracket if you want to mount a fuel or water can to the back of your Four Wheel Camper.

The system is used in conjunction with your AT Can Holder and Water Can or Fuel Can.

Order the Corner Bracket, Fuel Can Holder, and Water Can or Fuel Can at the same time and get the complete set up.

Some assembly is required, you will have to drill three mounting holes in the Fuel Can Holder so you can mount the bracket to the Fuel Can Holder. You will also have to drill holes in the aluminum support plate and into the overhang on the camper. If you have fold down rear steps or underbody lighting you may have to notch the holder or plate to accommodate a correct fitment.

Starting in 2018 Four Wheel Campers moved the corner brackets used to attach the camper jacks up one inch above the outside corners to make room for the edge trim. Please let us know in the notes section if your camper has the raised corner brackets. Please also let us know which side, passenger or driver's side the holder is to be mounted, and which model of camper the bracket will be fitted to.

Includes all mounting hardware, does not include can holder or can.

These cans are from the Factory that has been manufacturing them for the military for over 80 years.Original Jerry cans made to the highest specs. Fully paint-coated inside and outside. Equipped with a full internal breather pipe for splash-proof pouring.

The highest quality Jerry can out there. Original Mil Spec. Approved for use in all States, (EPA and CARB approved). Each can comes with a safety spout (pour spout) attached and also has an adapter for vehicles with smaller filler receivers.

• Manufactured from 0.9mm Cold Rolled Steel ( DC 04 EN 10130).
• Dual pan construction. Unique wide channel breather for better smoother pouring.
• Seam welded for extra strength.
• Three Handle Configuration.
• Leakproof Bayonet Closure.
• Locking pin in cap.
• Strengthened hinge on cap to prevent accidental bending when closing.
• Cap designed to hold open when discharging the can.
• Lined inside with fuel resistant Rezol enamel to prevent rusting.
• Painted exterior epoxypolyester powder coat.
• Holds 5 gallons.
• The only Jerry Can like this approved and legal in all States!
• Comes with certified pour spout

AT uses 0.125” thick, The redesigned holder is clear coated and made from plates that are riveted together, they have an industrial look to them. These strong and functional each unit weighs 6 lbs.

The holder has built in attachment points so it can be mounted in any variety of positions, apart from upside down.

There are two different straps for the Scepter style cans.

The default strap is for the fuel can, Diesel or Gasoline, and it is included in the price of the can holder. This strap only fits the Diesel or Gasoline MFC cans

The strap for the Scepter Water Can (MWC) is the only strap that works with the water can, due to the small breather cap on the main fill cap. This strap has to be selected when you purchase this product. We do not carry many of these MWC straps in stock, and selecting this style of strap may delay your order. If you have a Scepter fuel can, either diesel or gasoline use the default MFC strap. The strap for the Scepter Water Can (MWC) will also work with the Military Diesel and Gasoline cans (MFC), but as stated is stocked in low volumes.

Holder dimensions: 19.875" x 14.75" x 7.375" (505mm x 375mm x 187mm)

AT uses 0.125” thick, The redesigned holder is clear coated and made from plates that are riveted together, they have an industrial look to them. These strong and functional each unit weighs 6 lbs.

The holder has built in attachment points so it can be mounted in any variety of positions, apart from upside down.

Holder dimensions: 19.875" x 14.75" x 7.375" (505mm x 375mm x 187mm)

CARB 1 cans have a flat screw on cap, as seen in the picture below, and the spout is seperate from the can.

One strap is included when ordering a can holder.

CARB 2 cans have the spout inside the cap, and a small raised portion in the center of the cap, as seen in the picture below.

AT uses 0.125” thick, The redesigned holder is clear coated and made from plates that are riveted together, they have an industrial look to them. These strong and functional each unit weighs 6 lbs.

The holder has built in attachment points so it can be mounted in any variety of positions, apart from upside down.

Uses the CARB 2 strap.

Holder dimensions: 19.875" x 14.75" x 7.375" (505mm x 375mm x 187mm)

One strap is included when ordering a can holder.

AT uses 0.125” thick, clear anodized aluminum straps for their holders.

The straps are unique to three different styles of cans, please specify when ordering:

Strap 1: To be used with CARB 1 fuel cans. These cans have a separate spout that does not fit inside the can.

Strap 2: To be used with CARB 2 fuel cans (the spout fits inside the fuel can), all NATO cans, and Scepter Military Gasoline and Diesel cans.

Strap 3: To be used with Scepter Military Water Cans

One strap is included when ordering a can holder. Only order extra straps for you cn holder on this page.

CARB compliant bayonet style fuel can spout. Fits all NATO style fuel cans with a bayonet closure.

The spout also has an adapter for vehicles with smaller filler receivers.

5lb Propane Bracket fitted to rear roll cage of the Jeep JK. Fits Manchester 5lb tanks only.

This kit includes the External Corner Mount Bracket that mounts to the Jeep Wrangler JK/JKU hard top, the 5 lb. propane bracket, and the propane cylinder. Mounting requires drilling into the hard top and inserting well plugs, which are provided. 

You can also buy the External Corner Bracket, propane cylinder bracket, and 5 lb. propane cylinder separately. 

This External Corner Mount Bracket mounts to the drivers side rear corner of the Jeep Wrangler JK/JKU hard top. Mounting requires drilling into the hard top and inserting well plugs, which are provided. This bracket is used in conjunction with our 5 lb. propane bracket and our 5 lb. propane cylinder.

You can also buy the complete kit that includes all three items here. 

The MWC 20 litre (5 gal.)

Scepter’s MWCs (Military Water Cans) are BPA (Bisphenol A) free.

Each MWC has a uniform, integrated single handle that, in the dark, prevents mistaking it for the three handled MFC.

Scepter's MWCs are supplied to military armed forces around the world as accessories on OEM vehicles and for OEM military auxiliary equipment and systems.

Height:  18.8”   Length - 13.7”   Width - 6.8”