Fuel, Propane and Water

5 lb. Propane Cylinder Bracket. AT's aluminum propane bracket, sized to fit a 5 lb. propane tank. Compact and light weight.

(DOT 5 lb cylinder 12" H x 8" diameter).

AT has designed an aluminum bracket for the Manchester Tank 10 lb propane cylinder.

The brackets are made from 1/8" thick aluminum and have rubber bump stops to hold the cylinder off the bracket. The cylinder is held in place by two stainless steel T Bolt clamps. There are pre-drilled holes in the bracket.

BRACKET:
Size: 12.375" T x 9.5" W x 4.75" D (314mm x 241mm x 120mm)
Weight:2.5 Lbs (1.13 Kg.)
1/8" Thick aluminum
Two Stainless Steel constant tension clamps

The bracket and cylinder combined weight is 17 lbs.(7.7 Kg) and it is 18" tall (457mm) with a maximum diameter of 10.3"(226mm).

CYLINDER:
The Manchester 10 lb propane cylinder that fits into this bracket is 17.4" tall x 8.9" in (442mm x 226mm) diameter and holds 2.4 gallons of propane.

Use the AT Corner Bracket if you want to mount a fuel or water can to the back of your Four Wheel Camper.

The system is used in conjunction with your AT Can Holder and Water Can or Fuel Can.

Order the Corner Bracket, Fuel Can Holder, and Water Can or Fuel Can at the same time and get the complete set up.

Some assembly is required, you will have to drill three mounting holes in the Fuel Can Holder so you can mount the bracket to the Fuel Can Holder. You will also have to drill holes in the aluminum support plate and into the overhang on the camper. If you have fold down rear steps or underbody lighting you may have to notch the holder or plate to accommodate a correct fitment.

Starting in 2018 Four Wheel Campers moved the corner brackets used to attach the camper jacks up one inch above the outside corners to make room for the edge trim. Please let us know in the notes section if your camper has the raised corner brackets. Please also let us know which side, passenger or driver's side the holder is to be mounted, and which model of camper the bracket will be fitted to.

Includes all mounting hardware, does not include can holder or can.

The AT Scepter Can Holder is made from 0.125” thick aluminum. The holder is clear coated and made from plates that are riveted together. These industrial grade holders are strong and functional. The holder has built in attachment points so it can be mounted in any variety of positions, apart from upside down.

The strap for the Scepter Can works with the water can (MWC) with the small breather cap on the main fill cap and the fuel can (MFC).  

Holder dimensions: 19.875" x 14.75" x 7.375" (505mm x 375mm x 187mm)

AT uses 0.125” thick, The redesigned holder is clear coated and made from plates that are riveted together, they have an industrial look to them. These strong and functional each unit weighs 6 lbs.

The holder has built in attachment points so it can be mounted in any variety of positions, apart from upside down.

Uses the CARB 2 strap.

Holder dimensions: 19.875" x 14.75" x 7.375" (505mm x 375mm x 187mm)

One strap is included when ordering a can holder.

AT uses 0.125” thick, clear anodized aluminum straps for their holders.

The straps are unique to three different styles of cans, please specify when ordering:

Strap 2: To be used with CARB 2 fuel cans (the spout fits inside the fuel can), all NATO cans, and Scepter Military Gasoline and Diesel cans.

Strap 3: To be used with Scepter Military Water Cans

One strap is included when ordering a can holder. Only order extra straps for you cn holder on this page.

This kit includes the External Corner Mount Bracket that mounts to the Jeep Wrangler JK/JKU hard top, the 5 lb. propane bracket, and the propane cylinder. Mounting requires drilling into the hard top and inserting well plugs, which are provided. 

You can also buy the External Corner Bracket, propane cylinder bracket, and 5 lb. propane cylinder separately. 

This External Corner Mount Bracket mounts to the drivers side rear corner of the Jeep Wrangler JK/JKU hard top. Mounting requires drilling into the hard top and inserting well plugs, which are provided. This bracket is used in conjunction with our 5 lb. propane bracket and our 5 lb. propane cylinder.

You can also buy the complete kit that includes all three items here. 

The AT Overland Rotopax Holder is designed specifically for the Gen-2, 2 Gallon Rotopax container and fits Four Wheel Campers or any camper using the 13” Rieco Titan HD Corner Bracket system. The holder fits on the rear bracket of a slide-in or flatbed camper, and on the front bracket of any camper, including the Project M provided that there is 4” of space between the cab and camper. The holder includes all necessary mounting hardware and a padlock with 3 keys. If you order more than one holder, padlocks will be keyed alike.

Dimensions: 3.625” thick x 18.375” high x 16.625” wide

Includes:
- Rotopax holder
- All necessary mounting hardware
- Padlock with (3) keys

Weight:
- 8 lbs. solo
- 12 lbs. with Rotopax empty
- 24 lbs. filled with gasoline
- 28 lbs. filled with water

Rotopax shown are not included, but can be added to your order.