Products

10 lb. Propane Cylinder.

10 lb. propane tank. Compact and light weight.

(DOT 10 lb cylinder 17.4" H x 8.9" diameter) .
Contains 2.4 gallons of propane.

AT has designed an aluminum bracket for the Manchester Tank 10 lb propane cylinder.

The brackets are made from 1/8" thick aluminum and have rubber bump stops to hold the cylinder off the bracket. The cylinder is held in place by two stainless steel T Bolt clamps. There are pre-drilled holes in the bracket.

BRACKET:
Size: 12.375" T x 9.5" W x 4.75" D (314mm x 241mm x 120mm)
Weight:2.5 Lbs (1.13 Kg.)
1/8" Thick aluminum
Two Stainless Steel constant tension clamps

The bracket and cylinder combined weight is 17 lbs.(7.7 Kg) and it is 18" tall (457mm) with a maximum diameter of 10.3"(226mm).

CYLINDER:
The Manchester 10 lb propane cylinder that fits into this bracket is 17.4" tall x 8.9" in (442mm x 226mm) diameter and holds 2.4 gallons of propane.

5 lb. Propane Cylinder.

5 lb. propane tank. Compact and light weight.

(DOT 5 lb cylinder 12" H x 8" diameter).

5 lb. Propane Cylinder Bracket. AT's aluminum propane bracket, sized to fit a 5 lb. propane tank. Compact and light weight.

(DOT 5 lb cylinder 12" H x 8" diameter).

AT uses 0.125” thick, The redesigned holder is clear coated and made from plates that are riveted together, they have an industrial look to them. These strong and functional each unit weighs 6 lbs.

The holder has built in attachment points so it can be mounted in any variety of positions, apart from upside down.

Holder dimensions: 19.875" x 14.75" x 7.375" (505mm x 375mm x 187mm)

CARB 1 cans have a flat screw on cap, as seen in the picture below, and the spout is seperate from the can.

One strap is included when ordering a can holder.

CARB 2 cans have the spout inside the cap, and a small raised portion in the center of the cap, as seen in the picture below.

AT uses 0.125” thick, The redesigned holder is clear coated and made from plates that are riveted together, they have an industrial look to them. These strong and functional each unit weighs 6 lbs.

The holder has built in attachment points so it can be mounted in any variety of positions, apart from upside down.

Uses the CARB 2 strap.

Holder dimensions: 19.875" x 14.75" x 7.375" (505mm x 375mm x 187mm)

One strap is included when ordering a can holder.

AT uses 0.125” thick, The redesigned holder is clear coated and made from plates that are riveted together, they have an industrial look to them. These strong and functional each unit weighs 6 lbs.

The holder has built in attachment points so it can be mounted in any variety of positions, apart from upside down.

There are two different straps for the Scepter style cans.

The default strap is for the fuel can, Diesel or Gasoline, and it is included in the price of the can holder. This strap only fits the Diesel or Gasoline MFC cans

The strap for the Scepter Water Can (MWC) is the only strap that works with the water can, due to the small breather cap on the main fill cap. This strap has to be selected when you purchase this product. We do not carry many of these MWC straps in stock, and selecting this style of strap may delay your order. If you have a Scepter fuel can, either diesel or gasoline use the default MFC strap. The strap for the Scepter Water Can (MWC) will also work with the Military Diesel and Gasoline cans (MFC), but as stated is stocked in low volumes.

Holder dimensions: 19.875" x 14.75" x 7.375" (505mm x 375mm x 187mm)

AT uses 0.125” thick, clear anodized aluminum straps for their holders.

The straps are unique to three different styles of cans, please specify when ordering:

Strap 1: To be used with CARB 1 fuel cans. These cans have a separate spout that does not fit inside the can.

Strap 2: To be used with CARB 2 fuel cans (the spout fits inside the fuel can), all NATO cans, and Scepter Military Gasoline and Diesel cans.

Strap 3: To be used with Scepter Military Water Cans

One strap is included when ordering a can holder. Only order extra straps for you cn holder on this page.

The lower slide is built to hold the JK Partner Steel Stove, and the upper slide to hold an Engel 45, a National Luna Weekender Fridge, or a ARB 50 qt . For easy of fitting a mounting plate is used to secure the fridge to the slide, it can also be bolted directly to it.

A Partner Steel Stove has been made specifically to fit the combo slide and has the controls built into the end of the unit.

This is a two level fridge slide. The Upper slide for a fridge, the lower slide for a partner steel stove (not included). The slides are rated at 500 lb rated and lock in and out. If a stove is not fitted to the lower slide it can be used as a storage shelf.

The Combo Slide is:
29"(737mm) long without the stove
16"(406mm) wide and 5"(127mm) tall.

Normally sold in conjunction with the JK Stove

14 day lead time ordering to shipping.

These cans are from the Factory that has been manufacturing them for the military for over 80 years.Original Jerry cans made to the highest specs. Fully paint-coated inside and outside. Equipped with a full internal breather pipe for splash-proof pouring.

The highest quality Jerry can out there. Original Mil Spec. Approved for use in all States, (EPA and CARB approved). Each can comes with a safety spout (pour spout) attached and also has an adapter for vehicles with smaller filler receivers.

• Manufactured from 0.9mm Cold Rolled Steel ( DC 04 EN 10130).
• Dual pan construction. Unique wide channel breather for better smoother pouring.
• Seam welded for extra strength.
• Three Handle Configuration.
• Leakproof Bayonet Closure.
• Locking pin in cap.
• Strengthened hinge on cap to prevent accidental bending when closing.
• Cap designed to hold open when discharging the can.
• Lined inside with fuel resistant Rezol enamel to prevent rusting.
• Painted exterior epoxypolyester powder coat.
• Holds 5 gallons.
• The only Jerry Can like this approved and legal in all States!
• Comes with certified pour spout

Description:

• 12V DC severe duty winch rated at 12,500 lb pulling meets or exceeds your expectations.
• Heavy duty series wound motor equipped with thermal switch alters when motor over-heating.
• 4 equally positioned pin holes with a stainless steel ergonomic T-handle make it possible to clock in 90 degree Increments.
• Water-proof remote control with thermometric LED indicator w/5 m cord
• Tough aluminum die cast housings withstand strength of 2.0 x rated load of winch in foot forward mounting
• The U.S. Germany, U.K. France, etc patented mechanical cone brake outside the drum expedites heat dispersion. The greater the load on the rope, the greater amount of braking is generated by the mechanism.
• Meet SAE J706, CE Machinery Directive 2006/42/EC and CE Electromagnetic Compatibility Directive 2004/108/EC.

Specifications:

Limited time free shipping to US destinations within the lower 48 States

Description:

• 12V DC severe duty winch rated at 12,500 lb pulling meets or exceeds your expectations.
• Heavy duty series wound motor equipped with thermal switch alters when motor over-heating.
• 4 equally positioned pin holes with a stainless steel ergonomic T-handle make it possible to clock in 90 degree Increments.
• Water-proof remote control with thermometric LED indicator w/5 m cord
• Tough aluminum die cast housings withstand strength of 2.0 x rated load of winch in foot forward mounting
• The U.S. Germany, U.K. France, etc patented mechanical cone brake outside the drum expedites heat dispersion. The greater the load on the rope, the greater amount of braking is generated by the mechanism.
• Meet SAE J706, CE Machinery Directive 2006/42/EC and CE Electromagnetic Compatibility Directive 2004/108/EC.

Specifications:

Description:

• 12V DC severe duty winch rated at 9,500 lb pulling meets or exceeds your expectations.
• Heavy duty series wound motor equipped with thermal switch alters when motor over-heating.
• Water-proof remote control with thermometric LED indicator w/5 m cord
• New Intelligence Dashboard (IDB) and Power Cutout Switch
• Tough aluminum die cast housings withstand strength of 2.0 x rated load of winch
• The U.S. Germany, U.K. France, etc patented mechanical cone brake outside the drum expedites heat dispersion. The greater the load on the rope, the greater amount of braking is generated by the mechanism.
• Meet SAE J706, CE Machinery Directive 2006/42/EC and CE Electromagnetic Compatibility Directive 2004/108/EC.

Specifications:

Limited time free shipping to US destinations within the lower 48 States

Description:

• 12V DC severe duty winch rated at 9,500 lb pulling meets or exceeds your expectations.
• Heavy duty series wound motor equipped with thermal switch alters when motor over-heating.
• 4 equally positioned pin holes with a stainless steel ergonomic T-handle make it possible to clock in 90 degree Increments.
• Water-proof remote control with thermometric LED indicator w/5 m cord
• Tough aluminum die cast housings withstand strength of 2.0 x rated load of winch
• The U.S. Germany, U.K. France, etc patented mechanical cone brake outside the drum expedites heat dispersion. The greater the load on the rope, the greater amount of braking is generated by the mechanism.
• Meet SAE J706, CE Machinery Directive 2006/42/EC and CE Electromagnetic Compatibility Directive 2004/108/EC.

Specifications:

Limited time free shipping to US destinations in lower 48 States

An externally mounted shower unit. A great water source for the kitchen.

The fitting has a clean looking appearance, it's low profile and the cover seals to keep out dust and moisture.

The hose snaps into the fitting and is rotated to get the required water temperature.

The External shower kit includes:

Shower head and hose
Mixer valve
Mounting assembly

The shower unit is fitted with Whale fast disconnect fittings. We sell adapters from the fast disconnect system to a barbed fitting for standard hose, or a complete Whale fast disconnect system. To put a kit together for you we would need a schematic of your plumbing system, or discuss it with you on the phone.

If you require just the barb fittings please contact our office as these items are sold seperately.

If you want a full Whale fast disconnect to go along with the pump please call us for more information.

Water storage, pump, and water heater are available through AT.

For a pictorial display of how this unit works click here.

 Currently only available in gray.

Use the AT Corner Bracket if you want to mount a fuel or water can to the back of your Four Wheel Camper.

The system is used in conjunction with your AT Can Holder and Water Can or Fuel Can.

Order the Corner Bracket, Fuel Can Holder, and Water Can or Fuel Can at the same time and get the complete set up.

Some assembly is required, you will have to drill three mounting holes in the Fuel Can Holder so you can mount the bracket to the Fuel Can Holder. You will also have to drill holes in the aluminum support plate and into the overhang on the camper. If you have fold down rear steps or underbody lighting you may have to notch the holder or plate to accommodate a correct fitment.

Starting in 2018 Four Wheel Campers moved the corner brackets used to attach the camper jacks up one inch above the outside corners to make room for the edge trim. Please let us know in the notes section if your camper has the raised corner brackets. Please also let us know which side, passenger or driver's side the holder is to be mounted, and which model of camper the bracket will be fitted to.

Includes all mounting hardware, does not include can holder or can.

CARB compliant bayonet style fuel can spout. Fits all NATO style fuel cans with a bayonet closure.

The spout also has an adapter for vehicles with smaller filler receivers.

THE 5TH GEN WITH THE THIRD ROW SEAT MODEL 4RUNNERS. THE THIRD ROW DELETE MODEL IS ONLY AVAILABLE IN LOW PROFILE PLATE BASED MODELS.

40% AND 60% Sleeping Platforms are designed for 2010-Current Toyota 4Runner WITH THE 3rd Row Seat Delete Plate and are designed to remain flat and even with the rear plate. As shown in the pictures.

Overall length is 73", our taller clients push the front seats forward and stuff bags or pillows behind the seats to extend the sleeping area.

Includes fasteners and straps to secure sleeping platform to the back of an existing Goose Gear module and floor. Does not require drilling of the vehicle.

In the third row model 4Runner's, the 60% delete is on the Drivers Side and the 40% is on the Passengers side of the vehicle.

All sleeping platforms require the rear plate system for proper installation. As seen here 5th Gen 4Runner 3rd Row Delete Plate

 With the 4Runner STANDARD PROFILE sleeping platform you can now set up your rig for stealth camping and get comfortable. With the standard profile version you can leave the second row seat backs in place and simply fold them forward, but the seat bottoms must be removed for installation. The good news is that the lower seat section is held in with only two easy access bolts per side. If you remove the seat back as well, you will gain a great deal of additional storage as well as saving weight in your rig.

There are two models and three height options. The first is the Drivers side platform and covers the 40% side of the rear seat. The second is the passengers side platform and covers the 60% side of the rear seat. An access door from the top as well as side access when the passenger doors are open makes for an incredible amount of storage in the center of your vehicle and at the lowest point which is great for vehicle stability.

***The STANDARD PROFILE sleeping platforms for the 5th Gen 4Runner require the Goose Gear Plate and Goose Gear SUV drawer modules in 8", 10" or 12" heights to attach and are not included in this pricing. Does not require cutting or drilling of any part of the vehicle.***

Overall length is 76", our taller clients push the front seats forward and stuff bags or pillows behind the seats to extend the sleeping area.

40% and 60% Sleeping Platforms are designed for 2010-current Toyota 4Runner (without third row seat option only)

The 4Runner sleeping platforms require the rear 4Runner plate system and a drawer module in 8" - 10" or 12" height with the 8" and 10" being the most popular. Plate Systems can be found here 

Trail4r.com Installation Guide

The Goose Gear 4Runner Low Profile Sleeping System

With the 4Runner LOW PROFILE-PLATE BASED sleeping platform you can now set up your rig for stealth camping and get even more comfortable with more interior height. The first model is the Drivers side platform and covers the 40% side of the rear seat which must be completely removed for installation. The second model is the passengers side platform and covers the 60% side of the rear seat which must be completely removed for installation. An access door from the top as well as side access when the passenger door is open makes for a great amount of storage right in the center of your vehicle and at he lowest point which is great for vehicle stability.

***The LOW PROFILE sleeping platforms for the 5th Gen 4Runner do require the Goose Gear Plate but do not require a Goose Gear Storage Module. Does not require cutting or drilling of any part of the vehicle.***

Overall length is 73", our taller clients push the front seats forward and stuff bags or pillows behind the seats to extend the sleeping area.

40% and 60% Sleeping Platforms are designed for 2010-Current Toyota 4Runner (without third row seat option only)

The Goose Gear Alu-Box Top Plate Kit takes the lightweight and rugged Alu-Box aluminum storage boxes to the next level. It turns them into a solid step and gives them a solid top of sitting upon at camp. It also makes a great table when sitting around the campfire.

NEW DESIGN - Allows for proper stacking of Alu-Box's too.

Kit includes: top plate covered in Bullet Liner coating on all sides, stainless steel hardware for mounting

Installation requires drilling four holes into your Alu-Box to secure the top plate.

The Alu-Box is sold separately and not included with the kit.

AluCab Canopy Camper Drawers feature dovetailed Baltic Birch drawer boxes with full extension drawer guides. This unit fits both the 5' and the 6' Chevy Colorado's and will also fit on either side of the vehicle, Passengers and Drivers side.

AluCab Canopy Camper Drawers feature dovetailed Baltic Birch drawer boxes with full extension drawer guides. This unit fits both the 5' and the 6' Tacoma's and will also fit on either side of the vehicle, Passengers and Drivers side.

Module dimensions 25"w x 18.5"h x 13"d

Product images shown with TrekPak divider system and other camping items and are not included in drawer purchase.